日冠F6D8  2.4GHz接收机（D8制式兼容）说明书

简介：

 日冠F6D8 D8制式兼容接收机适用于任何使用Frsky D8协议的发射源，例如：Frsky模组DFT, DJT, DHT, XJT, XJT_lite, 等.

规格：

尺寸:         40x18x10mm

工作电流：     最大60mA

工作电压范围:  3.5V-10.0V

距离:          最大1.5km

重量:          5g

舵机通道速率:  18ms

SBUS通道速率:  9ms

6个PWM通道输出

1个SBUS通道输出

可设置的低压警报和回传信号警报

对码：

 先打开发射源并进入对码模式，然后按住F/S按钮的同时给接收机接通电源（不要连接任何其他外设）。接收机绿色LED灯常亮，然后遥控器蜂鸣器开始发出beebee声，接着接收机红色LED灯开始闪烁则表示接收机对码完成。关闭遥控器和接收机，然后再次给遥控器和接收机通电，此时绿色LED灯常亮表示接收机正在接收遥控器指令。

   本系列兼容接收机支持在接收机上设置失控保护，打开遥控器给接收机通电，在接收机和遥控器连接上的前30秒内，用户可以通过如下按键操作将此时遥控器的通道数据保存在接收机上（在设置失控保护的时候不建议连接其他外设）。在设置完成后我们建议给接收机稳定供电。

   重新对码后失控保护会失效

LED灯状态定义：

距离检查:

 我们建议用户在使用新绑定的接收机飞行前做一次距离检查。

F6D8 CompatibleReceiver Manual

Introduction:

      Corona F6D8 D8 Compatible receiver isavailable for any TX that use the Frsky D8 protocol, such as FrSky two waytelemetry modules: DFT, DJT, DHT, XJT, XJT_lite, etc.

Specifications:

Dimension: 40x18x10mm

Weight: 5g

Operating VoltageRange: 3.5V-10.0V

Operating Current: Max60mA

Operating Range: Fullrange (max 1.5km)

Servo Frame Rate:18ms

SBUS Frame Rate: 9ms

Features:

      Six channels of PWM output for servos.

      One SBUS channel for special usage(connect FC or expand servo channel).

That canbe set the alarm warning on low voltage and return signal in the TX

Bind procedure:

First, turnon the TX and swicth to Bind mode. Second, power on the receiver whileholding the F/S button on the receiver (not connect any servo or other device) and you can see agreen LED going on steady on the receiver. And buzzer begins to sound beebee.The red LED on the receiver will flash, indicating the bind iscompleted. Turn off both the transmitter and the receiver. Turnon the transmitter and power on the receiver. The greenLED that going on steady on the receiver indicates that the receiver isreceiving commands from the transmitter.

Failsafe Setting:

    The compatible receivers support failsafe seton the receiver. Turn on the transmitter and power on the receiver. User canpress and release the F/S button as pictured and all channels data will berecorded by the receiver in the first 30s before receivers and TX are connected.When operating failsafe setting, it is not recommended that servos or otherdevices connect with the receiver. After completing failsafe setting, a stablepower supply to the receiver is recommended.

      Failsafe setting will be cancelled whenresetting the bind procedure

LED Status Indication